Re-using the bracket

Luckily the bracket was pretty good, and I think sandblasting it and remake the reinforcement will make it good as new. There are pretty much work to recreate all these details... Always a little more than you think...

Rear bodymount

After visiting Bad Camberg, the spirit to finnish the zwitter was back again. Sourcing som good NOS welding parts made the job more greatful. I started to drill out the spotwelds on the existing bodymount with the backplate, because some rust was showing through. After removing the 3 layer plate, a LOT of rust came foreward....

Collecting pieces

The choice of VW happenings to visit this summer was Bug Run in Sweden and Bad Camberg in Germany. They both have a swap meet, and the the best in each division. Bug Run swaps are the best in Scandinavia, and the BC is world class. Even on a limited budget, due to house building, I managed to track down some items for the zwitter that I have been looking for.

In the "pile of shit" are for example a KDF fanhouse plate, a NOS vdo fuelgauge with sender, a Störk temperature gauge, OG brakefuel reservoir w/floater, NOS welding parts, OG zwitter bonnet handle, and some split rubber "hard to find".... And some other "juggel" that may be used for the car...

A new assistent

It has been a couple of months with little progression on the Zwitter. Most due to other projects as the Kvikk engine for the "Rallye-bug" and other tasks in the workshop. Some of the time is used to collect and sort out parts as well. Some of the things purchased this spring, was a new assistent for the shop. This will be very helpful when all the pieces of the car is going back together. It's great to be organized. The Hazet assisten is from the late 60ies as far as I can sort out. It's in great condition, and of course it will stay with it's original paint and patina =)

Hopefully this assistent will help speeding up my project.... (Before and after pictures)

A lot of air

This picture helps to make the decision of using danish steel even easier =)

Rear right corner

This is far whorse than the left rear corner. Nothing is left of the rear corner, and heavy surgery is needed. To get to the rusted area, the heater tube under the rear seat had to be removed. I cut it in a way that the top cover will hide the welding when finnished. The job now is to find out where to cut and replace with fresh metal. Here I see no other way than to use some danish metal to replace the rusted area. It's to huge for me to create, as there are few ends to meassure from.

Starting out back

Some exitement was certainly present when it came to removing the rear fender. After struggeling with both the front fenders, I expected nothing less here. But surprisingly it seemed that all the bolts and the fender had been removed at some point before, and the bolts could be removed by hand.

Right front corner

Some progression is visible on my project, but not as much as hoped. But the timewindow for this car is wide, and I'm in no hurry. Bulding piece by piece, the front end is becomming more solid each day. The regulator on the welder broke last nigt, so I didn't finish welding the last two pieces of the corner. But there is only filling of spotwelds and grinding left before anti-rust treatment and painting.

Backside of the medallion

After inspecting the backside of the H-apron, it seemes to be quite some work needed to make this baby shine again =)

Nice ass

A well formed rear end is never wrong in any way. The rear apron of a classic beetle is no exeption. As seen in the pictures posted on the zwitter, the car had a modern rear apron mounted at some point. This will of course be changed for the well known H-apron. These are not easy to come by, and to find an uncut example is almost impossible. Repro versions are on the marked, but there is always something about the real thing. After a tip from Fürsten, I collected a H-apron last night, although in a cut version. Having no experience in restoring this piece, it looks possible to reverse it back to a solid apron. Some pictures of the operation will follow.

Inside right side

On this side I did a little twist to the welding of the ouside channel. Because it was more solid than the other side, I made a more solid overlap weld. As you see in the pictures, there are still some pices to make.

Repeating procedures

To get the corner aligned again, I used measuring points from the other corner to get the pieces right. I started with the outer channel, and the cut the bottom part and tack welded it in place.

Corner nr. 2

The right side corner of the front heaterchannel, was even worse than the left. After cutting out the rusted pieces, there was not a lot of intersection points left. On this side the front wall was rotten on the underside all the way up.

And wholaaa...

Sometimes it's better to act than think to much... In this case the result came out better than expected. Porsche sparewheel wide 5? Formel-Vee? Classic racing? E-bay?

Struggling through

It's surprisingly not the funniest job at all times to weld, weld and weld... To get inspiration to start again, day after day on removing rust, it's important to have some visions of the project.

And a very important issue of a project is the wheels. I have many ideas in my head, and one of them is spinning around the wheel shown in the picture. This is a 911/912 Porsche wheel, and would fit an outlavws car quite nice... keep on dreaming =)

The outside corner

Here is the result of the outside corner. It may not be professional, but with some sealing of the welding and grinding of the surfaces, the result will be good enough to last another generation. I think the most important procedure will be the rustproofing inside the channels. This frontpiece welded in, will be exposed for hard conditions, and therefore I painted it with "weld through" paint on the inside of the channel.

The next corner

Hopefully the tricky parts will be easier to make on the next corner. Can you spot the intersection point on this corner? It's not easy to make these parts without measuring from a other car. Buying the channel bottoms from Wolfparts has been great help. Just three more corners to go.....

The first complete corner

The extention of the front wall and bottom piece, was a tricky part to make. But after several cardboard models and testing, the pieces seemed to fit. Of course it's easier to make the cardboard models when you have two splits to compare it to. After adjusting a little bit, the final piece was welded in. And then we have the first corner of the car rock solid. A little more welding and grinding needed to get the paint-ready finnish.

Towards a personal milestone

It has proven to take some time and skill to weld up the heaterchannels to look as good as stock. After fitting the heaterchannel bottom last time, the contour of the corner came back. First step was to extend the front side of the front wall, and to make and weld in the inner channel.

Front corner

At last I got some speed on the welding again. During one evening I managed to finish up the inner wing and started working on the heatercahnnel. I replaced the bottom part with goods from Wolfparts, and made the rest by papercutting and fitting before welding. The bottom and outer side of the left channel are now OK. Just some grinding and welding needed to finnish it up. A good feeling to se things look like new again =)